View previous topic :: View next topic |
Author |
Message |
Ron Palgrave Registered User
Joined: 30 Jan 2006 Posts: 21 Location: Tyneside
|
Posted: Wed Feb 10, 2021 3:53 pm Post subject: Exhaust manifold for Phase 1 with 1275 engine |
|
|
Looking for advice on source a Fabricated Exhaust manifold [ 3 into 2 into 1] to fit a Morris Minor based Phase 1 with 1275 A series engine. Looks like a standard Midget manifold hangs down too much. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Alan Smith Registered User
Joined: 10 Jan 2016 Posts: 90 Location: Littleborough, Lancashire
|
Posted: Wed Feb 10, 2021 9:45 pm Post subject: |
|
|
Hi Ron
I have an MG Midget LCB manifold in the garage. I haven't test fitted it against my MM 1098 yet (planned 1275 cyl head in the future). I could get some approx. measurements from it, if that is any good for you?
Have you considered the Cooper S 3 branch manifold - highly rated - looks like it might fit?
Also, the Maniflow Cooper Freeflow - again highly rated - looks like it might be adaptable to fit by cutting and turning the bottom bend?
Good luck. _________________ Phase 1R Olympic
MM 1098 Engine & Gearbox |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
keith hamer Site Admin
![](images/avatars/287344a116971846e1.jpg)
Joined: 28 Jan 2006 Posts: 312 Location: Ellesmere Port
|
Posted: Thu Feb 11, 2021 9:14 am Post subject: Exhaust manifold |
|
|
We have fitted both 'A' series and 'B' series long centre branch manifolds to Olympics, both types require some form of modification to make them fit the Olympic application. _________________ Working to increase the profile of Rochdale Cars |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Alan Smith Registered User
Joined: 10 Jan 2016 Posts: 90 Location: Littleborough, Lancashire
|
Posted: Thu Feb 11, 2021 9:51 am Post subject: |
|
|
Hi Keith
Do you have any details and photos of the mods required, that you could share on the forum? _________________ Phase 1R Olympic
MM 1098 Engine & Gearbox |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Ron Palgrave Registered User
Joined: 30 Jan 2006 Posts: 21 Location: Tyneside
|
Posted: Thu Feb 11, 2021 10:38 am Post subject: 1275 exhaust manifold |
|
|
I was prepared to "cut and shut" a Midget exhaust, [which I have] but was concerned that later somebody would say "Why did'nt you just.........?"
Anyway thanks for your comments. I share Alan's interest in preliminary dimension. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Alan Smith Registered User
Joined: 10 Jan 2016 Posts: 90 Location: Littleborough, Lancashire
|
Posted: Thu Feb 11, 2021 11:03 am Post subject: |
|
|
I strongly agree with your approach Ron - "there's no point re-inventing the wheel", "we don't know what we don't know" and "we don't get if we don't ask". ![Very Happy](images/smiles/icon_biggrin.gif) _________________ Phase 1R Olympic
MM 1098 Engine & Gearbox |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|